Engineering report · reviewed against NEC 2026 & BS 7671:2018+A2
Engineering Breakdown: Running a BYD Atto 3 / Dolphin (7kW AC Charging) on the EG4 18kPV Hybrid Inverter + PowerPro 14.3kWh WallMount
When pairing the EG4 18kPV Hybrid Inverter + PowerPro 14.3kWh WallMount (14,336 Wh LiFePO4 capacity, 12,000 W continuous, 18,000 W surge) with a BYD Atto 3 / Dolphin (7kW AC Charging) (7,200 W running, 7,200 W starting surge), the system operates at 60% of continuous inverter capacity on a 230 V UK/EU/AU circuit. At a 100% duty cycle and 85% inverter efficiency, a full battery delivers roughly 1.7 hrs of off-grid runtime. Wiring the connection over a 7.5 m run calls for a 32 A MCB and 4.0 mm² copper, terminated at a Type 2 EVSE · IEC 60309 32A Commando connection.
1. Compatibility Verdict & Inverter Load Utilization
In UK/EU/AU 230 V mode the BYD Atto 3 / Dolphin (7kW AC Charging) loads the EG4 18kPV Hybrid Inverter + PowerPro 14.3kWh WallMount's inverter to 60% of its 12,000 W continuous rating and 40% of its 18,000 W surge rating. Both figures are under the 80% sustained-load guideline, so this is a comfortable, verified match with 4,800 W of spare capacity for lights, a router or a refrigerator on the same unit.
| Check | Load requires | EG4 18kPV Hybrid Inverter + PowerPro 14.3kWh WallMount provides | UK/EU/AU |
|---|---|---|---|
| Continuous output | 7,200 W | 12,000 W | Pass |
| Start-up surge | 7,200 W | 18,000 W | Pass |
| Voltage | 230 V | 230 V | Pass |
| Connection | Type 2 EVSE · IEC 60309 32A Commando | Hardwired consumer unit (RCBO protected) |
This is a 230 V market charging profile: the 7,200 W figure is the single-phase Type 2 (IEC 62196) rate of 31 A × 230 V. EV supply equipment is a constant-current load with no start-up surge, so the inverter only has to sustain the set current. To stay under the 80% sustained-load guideline, cap the charge current at 32 A in the vehicle or charger app, which holds the EG4 18kPV Hybrid Inverter + PowerPro 14.3kWh WallMount near 7,360 W. In the UK, a charge point must meet BS 7671 Section 722 and the Electric Vehicles (Smart Charge Points) Regulations; in Australia and New Zealand, AS/NZS 3000 Section 7 and local network limits apply. A full battery puts about 11.0 kWh into the pack after losses — roughly 62 km (38 miles) of range.
The EG4 18kPV Hybrid Inverter + PowerPro 14.3kWh WallMount is a hybrid solar inverter paired with rack or wall-mount batteries, wired into a split-phase load center. It is the most scalable option in our database for large 240V loads.
2. Real-World Runtime by Duty Cycle
Nameplate capacity is not usable capacity. DC-to-AC conversion, battery management overhead and cell protection reduce the 14,336 Wh rating to about 12,186 Wh of deliverable AC energy (85% system efficiency). EV charging runs at a fixed current, so the 100% row is the realistic figure; lower rows apply only if you schedule charging in intervals.
| Duty cycle | Average draw | Runtime (no solar) | Energy per 24 h |
|---|---|---|---|
| 25% | 1,800 W | 6.8 hrs | 43.2 kWh |
| 50% | 3,600 W | 3.4 hrs | 86.4 kWh |
| 65% | 4,680 W | 2.6 hrs | 112.3 kWh |
| 100% | 7,200 W | 1.7 hrs | 172.8 kWh |
Even at a 50% duty cycle the battery lasts 3.4 hrs, so plan on solar, grid or generator recharging for anything longer than an evening outage.
3. BS 7671 / IEC 60364 Breaker & Cable Sizing
IEC-based codes size protection by design current rather than a blanket 125% multiplier: Ib ≤ In ≤ Iz. At 230 V the load draws 31.3 A, so a 32 A Type B/C MCB with RCD protection applies. In the UK, BS 7671 Section 722 additionally requires a dedicated circuit and Type A or Type B RCD for EV charge points.
| One-way distance | MCB | Min. cable | Voltage drop |
|---|---|---|---|
| 7.5 m (25 ft) | 32 A | 4.0 mm² | 0.94% |
| 15 m (49 ft) | 32 A | 4.0 mm² | 1.88% |
| 22.5 m (74 ft) | 32 A | 4.0 mm² | 2.82% |
| 30 m (98 ft) | 32 A | 6.0 mm² | 2.52% |
Moving the EG4 18kPV Hybrid Inverter + PowerPro 14.3kWh WallMount from 7.5 m to 30 m away forces the conductor up from 4.0 mm² to 6.0 mm² — park the unit as close to the load as ventilation and weather protection allow.
4. Solar Array Recharge Time Breakdown
The EG4 18kPV Hybrid Inverter + PowerPro 14.3kWh WallMount accepts up to 18,000 W of photovoltaic input. Real arrays rarely deliver nameplate output, so we apply an 80% harvest factor for MPPT conversion, cell temperature and soiling, and convert hours to days using 4.5 peak-sun-hours — a conservative annual average for the US, southern Europe and Australia (UK winters can fall below 1.5).
| PV array | Real harvest | 0–100% recharge | Sun-days @ 4.5 PSH | Net with load @ 50% |
|---|---|---|---|---|
| 1,600 W | 1,280 W | 11.2 hrs | 2.5 | −2,320 W |
| 3,000 W | 2,400 W | 6.0 hrs | 1.3 | −1,200 W |
| 6,000 W | 4,800 W | 3.0 hrs | 0.7 | +1,200 W |
| 12,000 W | 9,600 W | 1.5 hrs | 0.3 | +6,000 W |
| 18,000 W | 14,400 W | 60 min | 0.2 | +10,800 W |
A typical 800 W portable array refills the battery in about 22.4 hrs of strong sun, while maxing out the 18,000 W input cuts that to 60 min. To fully offset the BYD Atto 3 / Dolphin (7kW AC Charging) at a 50% duty cycle (3,600 W average) during daylight you need roughly 4,500 W of panels, which this unit can accept.
5. Frequently Asked Questions
Can the EG4 18kPV Hybrid Inverter + PowerPro 14.3kWh WallMount run a BYD Atto 3 / Dolphin (7kW AC Charging)?
Yes. The EG4 18kPV Hybrid Inverter + PowerPro 14.3kWh WallMount delivers 12,000 W continuous and 18,000 W surge, covering the BYD Atto 3 / Dolphin (7kW AC Charging)'s 7,200 W running and 7,200 W start-up draw at 60% inverter utilization.
How many miles of range can the EG4 18kPV Hybrid Inverter + PowerPro 14.3kWh WallMount add to a BYD Atto 3 / Dolphin?
A full 14,336 Wh charge delivers about 11.0 kWh to the vehicle battery after inverter (85%) and on-board charger (90%) losses — roughly 38 miles at 3.5 mi/kWh. At the full 7,200 W charge rate that takes 1.7 hrs.
What breaker and wire size do I need to connect a BYD Atto 3 / Dolphin (7kW AC Charging) to the EG4 18kPV Hybrid Inverter + PowerPro 14.3kWh WallMount?
At 230 V the load draws 31.3 A. Under BS 7671 / IEC 60364 the protective device must be at least the design current (Ib ≤ In ≤ Iz), so use a 32 A MCB with RCD protection on 4.0 mm² copper cable for runs up to 7.5 m (0.9% voltage drop). Connection: Type 2 EVSE · IEC 60309 32A Commando.
How long does it take to recharge the EG4 18kPV Hybrid Inverter + PowerPro 14.3kWh WallMount with solar panels?
With an 800 W array and an 80% real-world harvest factor, a full recharge takes about 22.4 hrs of peak sun (5.0 days at 4.5 peak-sun-hours). At its maximum 18,000 W solar input it drops to 60 min.
Methodology & safety note
Specifications come from manufacturer datasheets in our open dataset; ampacity and resistance values follow NEC Table 310.16 and Chapter 9 Table 8, and BS 7671 Appendix 4. Calculations assume copper conductors, 30 °C ambient and no bundling derating. Inverter-to-panel connections require a listed transfer switch or interlock to prevent back-feeding the grid. These results are an engineering estimate, not a substitute for a licensed electrician and local permit. See our methodology and safety disclaimer.