Engineering report · reviewed against NEC 2026 & BS 7671:2018+A2
Engineering Breakdown: Running a 1.0 HP Deep Well Submersible Pump (240V) on the EcoFlow Delta Pro Ultra (1 Inverter + 1 Battery)
When pairing the EcoFlow Delta Pro Ultra (1 Inverter + 1 Battery) (6,144 Wh LiFePO4 capacity, 7,200 W continuous, 10,800 W surge) with a 1.0 HP Deep Well Submersible Pump (240V) (1,650 W running, 4,500 W starting surge), the system operates at 23% of continuous inverter capacity on a 240 V North American circuit and 23% on a 230 V UK/EU/AU circuit. At a 100% duty cycle and 85% inverter efficiency, a full battery delivers roughly 3.2 hrs of off-grid runtime. Wiring the connection over a 25 ft run calls for a 15 A breaker and 14 AWG copper, terminated at a NEMA L14-30P / Hardwired connection.
1. Compatibility Verdict & Inverter Load Utilization
In North American mode the 1.0 HP Deep Well Submersible Pump (240V) loads the EcoFlow Delta Pro Ultra (1 Inverter + 1 Battery)'s inverter to 23% of its 7,200 W continuous rating and 42% of its 10,800 W surge rating. Both figures are under the 80% sustained-load guideline, so this is a comfortable, verified match with 5,550 W of spare capacity for lights, a router or a refrigerator on the same unit.
| Check | Load requires | EcoFlow Delta Pro Ultra provides | US/NA | UK/EU/AU |
|---|---|---|---|---|
| Continuous output | 1,650 W | 7,200 W | Pass | Pass |
| Start-up surge | 4,500 W | 10,800 W | Pass | Pass |
| Voltage | 240 V / 230 V | 120/240 V / 230 V | Pass | Pass |
| Connection | NEMA L14-30P / Hardwired | NEMA L14-30R / TT-30R / 5-20R | UK/EU/AU: Hardwired via DP isolator · IEC 60309 32A | |
Pumps are short-cycling, high-inrush loads. A well or sump pump might run for only 1–3 minutes at a time, but every start pulls 4,500 W — 2.7× its 1,650 W running draw — as the motor accelerates a column of water. That is why a pump that "only uses 1,650 W" still trips undersized inverters. Deep-well submersibles in North America are almost always 240 V two-wire or three-wire motors, so a 120 V-only station cannot drive them without a step-up transformer. A larger pressure tank reduces the number of starts per hour and is a worthwhile upgrade for off-grid systems built around the EcoFlow Delta Pro Ultra (1 Inverter + 1 Battery).
The EcoFlow Delta Pro Ultra (1 Inverter + 1 Battery) is engineered as a whole-home backup system, typically wired through a smart panel or transfer switch so that selected circuits switch over automatically during an outage.
2. Real-World Runtime by Duty Cycle
Nameplate capacity is not usable capacity. DC-to-AC conversion, battery management overhead and cell protection reduce the 6,144 Wh rating to about 5,222 Wh of deliverable AC energy (85% system efficiency). Duty cycle is the share of each hour the load actually draws its running power — thermostats, pressure switches and intermittent use all lower it.
| Duty cycle | Average draw | Runtime (no solar) | Energy per 24 h |
|---|---|---|---|
| 25% | 413 W | 12.7 hrs | 9.9 kWh |
| 50% | 825 W | 6.3 hrs | 19.8 kWh |
| 65% | 1,073 W | 4.9 hrs | 25.7 kWh |
| 100% | 1,650 W | 3.2 hrs | 39.6 kWh |
Even at a 50% duty cycle the battery lasts 6.3 hrs, so plan on solar, grid or generator recharging for anything longer than an evening outage.
3. NEC 125% Breaker & Copper Wire Gauge Sizing
NEC 210.19(A) and 210.20(A) require conductors and overcurrent devices for continuous loads — anything running three hours or more, which includes EV charging and HVAC — to be rated at 125% of the load current. For this pairing: 1,650 W ÷ 240 V = 6.9 A, × 1.25 = 8.6 A, which rounds up to the next standard NEC 240.6 size of 15 A. The conductor must be protected by that breaker (75 °C ampacity at least 15 A) and keep round-trip voltage drop at or below 3%, so longer runs are upsized.
Voltage drop % = (2 × L × I × R) ÷ V × 100
North America (NEC, THHN copper, 75 °C)
| One-way distance | Breaker | Min. copper | Voltage drop | Note |
|---|---|---|---|---|
| 25 ft (7.6 m) | 15 A | 14 AWG | 0.44% | Sized by ampacity |
| 50 ft (15.2 m) | 15 A | 14 AWG | 0.88% | Sized by ampacity |
| 75 ft (22.9 m) | 15 A | 14 AWG | 1.32% | Sized by ampacity |
| 100 ft (30.5 m) | 15 A | 14 AWG | 1.76% | Sized by ampacity |
UK / EU / Australia (IEC 60364 / BS 7671, PVC copper, method C)
IEC-based codes size protection by design current rather than a blanket 125% multiplier: Ib ≤ In ≤ Iz. At 230 V the load draws 7.2 A, so a 10 A Type B/C MCB with RCD protection applies. In the UK, BS 7671 Section 722 additionally requires a dedicated circuit and Type A or Type B RCD for EV charge points.
| One-way distance | MCB | Min. cable | Voltage drop |
|---|---|---|---|
| 7.5 m (25 ft) | 10 A | 1.5 mm² | 0.57% |
| 15 m (49 ft) | 10 A | 1.5 mm² | 1.13% |
| 22.5 m (74 ft) | 10 A | 1.5 mm² | 1.70% |
| 30 m (98 ft) | 10 A | 1.5 mm² | 2.26% |
Because the current is modest, 14 AWG copper stays within the voltage-drop target all the way to 100 ft.
4. Solar Array Recharge Time Breakdown
The EcoFlow Delta Pro Ultra (1 Inverter + 1 Battery) accepts up to 5,600 W of photovoltaic input. Real arrays rarely deliver nameplate output, so we apply an 80% harvest factor for MPPT conversion, cell temperature and soiling, and convert hours to days using 4.5 peak-sun-hours — a conservative annual average for the US, southern Europe and Australia (UK winters can fall below 1.5).
| PV array | Real harvest | 0–100% recharge | Sun-days @ 4.5 PSH | Net with load @ 50% |
|---|---|---|---|---|
| 400 W | 320 W | 19.2 hrs | 4.3 | −505 W |
| 800 W | 640 W | 9.6 hrs | 2.1 | −185 W |
| 1,600 W | 1,280 W | 4.8 hrs | 1.1 | +455 W |
| 3,000 W | 2,400 W | 2.6 hrs | 0.6 | +1,575 W |
| 5,600 W | 4,480 W | 1.4 hrs | 0.3 | +3,655 W |
A typical 800 W portable array refills the battery in about 9.6 hrs of strong sun, while maxing out the 5,600 W input cuts that to 1.4 hrs. To fully offset the 1.0 HP Deep Well Submersible Pump (240V) at a 50% duty cycle (825 W average) during daylight you need roughly 1,050 W of panels, which this unit can accept.
5. Frequently Asked Questions
Can the EcoFlow Delta Pro Ultra (1 Inverter + 1 Battery) run a 1.0 HP Deep Well Submersible Pump (240V)?
Yes. The EcoFlow Delta Pro Ultra (1 Inverter + 1 Battery) delivers 7,200 W continuous and 10,800 W surge, covering the 1.0 HP Deep Well Submersible Pump (240V)'s 1,650 W running and 4,500 W start-up draw at 23% inverter utilization.
How long will the EcoFlow Delta Pro Ultra (1 Inverter + 1 Battery) run a 1.0 HP Deep Well Submersible Pump (240V)?
With 6,144 Wh of capacity and 85% inverter efficiency, expect about 3.2 hrs of continuous operation and 6.3 hrs at a 50% duty cycle. Adding solar input during the day extends this further.
What breaker and wire size do I need to connect a 1.0 HP Deep Well Submersible Pump (240V) to the EcoFlow Delta Pro Ultra (1 Inverter + 1 Battery)?
In the US, 1,650 W at 240 V is 6.9 A; applying the NEC 125% continuous-load rule gives 8.6 A, so use a 15 A breaker and 14 AWG copper for runs up to 25 ft (0.4% voltage drop). In 230 V markets the load draws 7.2 A, protected by a 10 A MCB on 1.5 mm² cable for runs up to 7.5 m. Receptacle: NEMA L14-30P / Hardwired (US) or Hardwired via DP isolator · IEC 60309 32A (UK/EU/AU).
How long does it take to recharge the EcoFlow Delta Pro Ultra (1 Inverter + 1 Battery) with solar panels?
With an 800 W array and an 80% real-world harvest factor, a full recharge takes about 9.6 hrs of peak sun (2.1 days at 4.5 peak-sun-hours). At its maximum 5,600 W solar input it drops to 1.4 hrs.
Methodology & safety note
Specifications come from manufacturer datasheets in our open dataset; ampacity and resistance values follow NEC Table 310.16 and Chapter 9 Table 8, and BS 7671 Appendix 4. Calculations assume copper conductors, 30 °C ambient and no bundling derating. Inverter-to-panel connections require a listed transfer switch or interlock to prevent back-feeding the grid. These results are an engineering estimate, not a substitute for a licensed electrician and local permit. See our methodology and safety disclaimer.