Engineering report · reviewed against NEC 2026 & BS 7671:2018+A2
Engineering Breakdown: Running a BYD Atto 3 / Dolphin (7kW AC Charging) on the EcoFlow Delta Pro Ultra (1 Inverter + 1 Battery)
When pairing the EcoFlow Delta Pro Ultra (1 Inverter + 1 Battery) (6,144 Wh LiFePO4 capacity, 7,200 W continuous, 10,800 W surge) with a BYD Atto 3 / Dolphin (7kW AC Charging) (7,200 W running, 7,200 W starting surge), the system operates at 100% of continuous inverter capacity on a 230 V UK/EU/AU circuit. At a 100% duty cycle and 85% inverter efficiency, a full battery delivers roughly 44 min of off-grid runtime. Wiring the connection over a 7.5 m run calls for a 32 A MCB and 4.0 mm² copper, terminated at a Type 2 EVSE · IEC 60309 32A Commando connection.
1. Compatibility Verdict & Inverter Load Utilization
In UK/EU/AU 230 V mode the BYD Atto 3 / Dolphin (7kW AC Charging) loads the EcoFlow Delta Pro Ultra (1 Inverter + 1 Battery)'s inverter to 100% of its 7,200 W continuous rating and 67% of its 10,800 W surge rating. The pairing works, but running above 80% for hours raises internal temperatures and fan noise, and leaves little room for other loads. Treat it as a dedicated circuit.
| Check | Load requires | EcoFlow Delta Pro Ultra provides | UK/EU/AU |
|---|---|---|---|
| Continuous output | 7,200 W | 7,200 W | Pass |
| Start-up surge | 7,200 W | 10,800 W | Pass |
| Voltage | 230 V | 230 V | Pass |
| Connection | Type 2 EVSE · IEC 60309 32A Commando | IEC 60309 16A Commando + Schuko / BS 1363 outlets |
This is a 230 V market charging profile: the 7,200 W figure is the single-phase Type 2 (IEC 62196) rate of 31 A × 230 V. EV supply equipment is a constant-current load with no start-up surge, so the inverter only has to sustain the set current. To stay under the 80% sustained-load guideline, cap the charge current at 25 A in the vehicle or charger app, which holds the EcoFlow Delta Pro Ultra (1 Inverter + 1 Battery) near 5,750 W. In the UK, a charge point must meet BS 7671 Section 722 and the Electric Vehicles (Smart Charge Points) Regulations; in Australia and New Zealand, AS/NZS 3000 Section 7 and local network limits apply. A full battery puts about 4.7 kWh into the pack after losses — roughly 26 km (16 miles) of range.
The EcoFlow Delta Pro Ultra (1 Inverter + 1 Battery) is engineered as a whole-home backup system, typically wired through a smart panel or transfer switch so that selected circuits switch over automatically during an outage.
2. Real-World Runtime by Duty Cycle
Nameplate capacity is not usable capacity. DC-to-AC conversion, battery management overhead and cell protection reduce the 6,144 Wh rating to about 5,222 Wh of deliverable AC energy (85% system efficiency). EV charging runs at a fixed current, so the 100% row is the realistic figure; lower rows apply only if you schedule charging in intervals.
| Duty cycle | Average draw | Runtime (no solar) | Energy per 24 h |
|---|---|---|---|
| 25% | 1,800 W | 2.9 hrs | 43.2 kWh |
| 50% | 3,600 W | 1.5 hrs | 86.4 kWh |
| 65% | 4,680 W | 1.1 hrs | 112.3 kWh |
| 100% | 7,200 W | 44 min | 172.8 kWh |
Even at a 50% duty cycle the battery lasts 1.5 hrs, so plan on solar, grid or generator recharging for anything longer than an evening outage.
3. BS 7671 / IEC 60364 Breaker & Cable Sizing
IEC-based codes size protection by design current rather than a blanket 125% multiplier: Ib ≤ In ≤ Iz. At 230 V the load draws 31.3 A, so a 32 A Type B/C MCB with RCD protection applies. In the UK, BS 7671 Section 722 additionally requires a dedicated circuit and Type A or Type B RCD for EV charge points.
| One-way distance | MCB | Min. cable | Voltage drop |
|---|---|---|---|
| 7.5 m (25 ft) | 32 A | 4.0 mm² | 0.94% |
| 15 m (49 ft) | 32 A | 4.0 mm² | 1.88% |
| 22.5 m (74 ft) | 32 A | 4.0 mm² | 2.82% |
| 30 m (98 ft) | 32 A | 6.0 mm² | 2.52% |
Moving the EcoFlow Delta Pro Ultra (1 Inverter + 1 Battery) from 7.5 m to 30 m away forces the conductor up from 4.0 mm² to 6.0 mm² — park the unit as close to the load as ventilation and weather protection allow.
4. Solar Array Recharge Time Breakdown
The EcoFlow Delta Pro Ultra (1 Inverter + 1 Battery) accepts up to 5,600 W of photovoltaic input. Real arrays rarely deliver nameplate output, so we apply an 80% harvest factor for MPPT conversion, cell temperature and soiling, and convert hours to days using 4.5 peak-sun-hours — a conservative annual average for the US, southern Europe and Australia (UK winters can fall below 1.5).
| PV array | Real harvest | 0–100% recharge | Sun-days @ 4.5 PSH | Net with load @ 50% |
|---|---|---|---|---|
| 400 W | 320 W | 19.2 hrs | 4.3 | −3,280 W |
| 800 W | 640 W | 9.6 hrs | 2.1 | −2,960 W |
| 1,600 W | 1,280 W | 4.8 hrs | 1.1 | −2,320 W |
| 3,000 W | 2,400 W | 2.6 hrs | 0.6 | −1,200 W |
| 5,600 W | 4,480 W | 1.4 hrs | 0.3 | +880 W |
A typical 800 W portable array refills the battery in about 9.6 hrs of strong sun, while maxing out the 5,600 W input cuts that to 1.4 hrs. To fully offset the BYD Atto 3 / Dolphin (7kW AC Charging) at a 50% duty cycle (3,600 W average) during daylight you need roughly 4,500 W of panels, which this unit can accept.
5. Frequently Asked Questions
Can the EcoFlow Delta Pro Ultra (1 Inverter + 1 Battery) run a BYD Atto 3 / Dolphin (7kW AC Charging)?
Yes. The EcoFlow Delta Pro Ultra (1 Inverter + 1 Battery) delivers 7,200 W continuous and 10,800 W surge, covering the BYD Atto 3 / Dolphin (7kW AC Charging)'s 7,200 W running and 7,200 W start-up draw at 100% inverter utilization, which is above the 80% guideline, so dedicate the unit to this load.
How many miles of range can the EcoFlow Delta Pro Ultra (1 Inverter + 1 Battery) add to a BYD Atto 3 / Dolphin?
A full 6,144 Wh charge delivers about 4.7 kWh to the vehicle battery after inverter (85%) and on-board charger (90%) losses — roughly 16 miles at 3.5 mi/kWh. At the full 7,200 W charge rate that takes 44 min.
What breaker and wire size do I need to connect a BYD Atto 3 / Dolphin (7kW AC Charging) to the EcoFlow Delta Pro Ultra (1 Inverter + 1 Battery)?
At 230 V the load draws 31.3 A. Under BS 7671 / IEC 60364 the protective device must be at least the design current (Ib ≤ In ≤ Iz), so use a 32 A MCB with RCD protection on 4.0 mm² copper cable for runs up to 7.5 m (0.9% voltage drop). Connection: Type 2 EVSE · IEC 60309 32A Commando.
How long does it take to recharge the EcoFlow Delta Pro Ultra (1 Inverter + 1 Battery) with solar panels?
With an 800 W array and an 80% real-world harvest factor, a full recharge takes about 9.6 hrs of peak sun (2.1 days at 4.5 peak-sun-hours). At its maximum 5,600 W solar input it drops to 1.4 hrs.
Methodology & safety note
Specifications come from manufacturer datasheets in our open dataset; ampacity and resistance values follow NEC Table 310.16 and Chapter 9 Table 8, and BS 7671 Appendix 4. Calculations assume copper conductors, 30 °C ambient and no bundling derating. Inverter-to-panel connections require a listed transfer switch or interlock to prevent back-feeding the grid. These results are an engineering estimate, not a substitute for a licensed electrician and local permit. See our methodology and safety disclaimer.